Inventory Of Eleven Usage Skills Of High-speed Labeling Machine

Sep 20, 2022

Leave a message

High-speed labeling machine is one of the production and processing equipment for many food, beverage, pharmaceutical, and daily chemical enterprises. It plays an increasingly important role in our lives. The birth of the labeling machine allows the packaging work to proceed smoothly.


 Not only that, It also improves the packaging grade, which is convenient for people to use, and increases the beauty and practicality, which has won everyone's love. So do you know how to use the labeling machine? Let's find out together.


The use of high-speed labeling machine skills:

1. The installation of the label must be in place. When wrapping the label, try to wrap it as neatly as possible. It is easier to break the label if it is crooked. After the label is installed, fix the position with the limit ring.


2. Adjust the conveying guide bar according to the width of the product to be labelled, and leave a gap of 1mm between the two guide bars and the product. However, general paper card products use unilateral guide bars, so it is only necessary to adjust the two ends of the conveying guide bars to be relatively flat.


3. Adjust the position of the Z-axis direction of the header according to the height of the product, so that the label roll can be pulled and the peeled label can be attached to the surface of the product in time. Generally, the header of cardboard is adjusted to the height where the peeling plate basically touches the surface of the product.


 For thicker products, such as boxes and books, the header should be adjusted to a height of 1-2mm between the peeling plate and the surface of the product. After the adjustment is completed, lock the Z-axis direction.


4. Adjust the target electric eye. Tear off a label that is about to enter the target measuring sensor area, long press the button on the target measuring sensor to enter the setting state, and manually pull the label roll on the manual interface of the touch screen, so that the backing paper from which the label is torn is completely sensed by the target measuring sensor.


 After the zone is selected, press the button on the target sensor again to confirm the completion of the setting. If the optical fiber sensor is used to detect the target, the preset value of the output signal on the amplifier is set according to the difference in the signal numbers taken by the label on the label roll and the backing paper.


5. Control the pre-stripping length of the label, usually the label is pre-stripped to a length of 1mm. It can be adjusted by moving the position of the measuring object electric eye.


6. Adjust the object sensor so that the product has a signal output when it passes through the front end of the sensor. (The sensor adjustment is set according to the type used and the instructions on the brand)


7. Adjust the conveying speed, and adjust the pulling speed of the header according to the existing conveying speed to match it. Each time the label is applied, the sound is very crisp, without any dragging sound, and the label will not wrinkle.


8. Adjust the overwriting mechanism. Generally, the standard covering mechanism adopts rollers, sponges and brushes. Cover Roller: Adjust slightly lower than the peeling plate and close to the peeling plate. Label-covering sponge and label-covering brush: adjust the length of the label to be peeled off and stick out about 10mm from the edge.


9. The control label is affixed to the area in the specified X-axis direction. Labeling is performed under the condition that the labeling delay in the touch screen parameters is 0, and the X-axis direction is adjusted forward and backward according to the situation that the labeling is advanced or too slow. 


If the label is peeled off in advance, it means that the sensor detects the product prematurely and moves the header to the negative direction of the X-axis; otherwise, moves the header to the positive direction of the X-axis. After the adjustment is completed, lock the X-axis direction.


If the adjustment seat has reached the limit and cannot meet the labeling requirements, the sensor position can be adjusted. If the label is peeled off in advance, the sensor can be moved in the positive direction of the X-axis; if the label is peeled off too late, the sensor will be moved in the negative direction of the X-axis.


 When the motion sensor limit cannot solve the premature peeling of the label, the labeling delay parameter can be set appropriately.


10. According to the labeling position of the product, adjust the position of the header in the Y-axis direction, so that the label is attached to the specified Y-axis direction. After adjustment, lock the Y-axis direction.


11. Adjusting the peeling plate is basically parallel to the surface of the product, which can be adjusted by adjusting the direction of the R-axis on the seat. After adjustment, lock the R-axis direction.