It is reported that in the process of producing capsules, some pharmaceutical companies, due to the fine powder, will produce defective appearances when the machine is filled, and it has always been necessary to manually "picking drugs" to remove them. The technical personnel of the pharmaceutical company carried out research on the subject, and through continuous optimization and continuous debugging of the capsule filling equipment, the rate of appearance defect products was reduced, and the labor cost was also greatly reduced.
The industry pointed out that the filling quality of the capsule filling machine is very important. With the tightening of industry supervision, this has become a problem of great concern to pharmaceutical companies. Therefore, the capsule filling machine equipment needs to continuously improve the equipment, optimize the equipment structure, and help pharmaceutical companies better Production.
"In addition to the quality of the equipment itself, the equipment environment, transportation process, and various stations will all have an impact on the filling quality." A technician from a filling machine manufacturer said that users need to pay special attention to several tasks of the equipment when operating the equipment. It includes the following parts.
First, the capsule U-turn and separation station.This station is the capsule feeding and separating mechanism, and the purpose is to feed the capsule into the module and separate the capsule body and capsule cap for the next step of drug filling.
Common problems of this station include poor separation, flying caps, etc. The technicians reminded that the pressure adjustment for vacuum separation should be appropriate, not too large or too small. Flying caps will occur if they are too small, and poor separation will occur if they are too small. At the same time, capsules must be purchased from regular manufacturers and passed inspection.
The second is the filling station. This station mainly controls the filling weight of the capsule contents. The main common problem is the unstable weight of the filling contents.
The reasons mainly include three aspects:
one is the poor alignment of the metering plate and the lower module, which makes the weight of some finished capsules always lighter. The technical staff pointed out that it is not easy to find the problem here. The user must assemble the device before production. The centering must be done well when debugging the equipment.
Second, the gap between the spacer block on the metering plate and the metering plate is too large, so that the medicine passes through the gap during filling. Flow into the metering hole causes the weight of the capsule to be too large. It is reported that it is generally better to adjust the gap between the spacer block and the measuring disc to 0.05~0.1mm. If it is too small, the measuring disc will be worn and the equipment will be damaged.
In addition, the height of the powder on the metering plate also has a certain effect on the filling weight. If the height of the powder is too low, the powder will not flow into the metering hole in time, causing the capsule to be lighter. If the height is too high, too much medicine will flow into the metering plate. The weight is too heavy.
Third, the waste capsule removal station. The function of this station is to discharge the poorly separated capsules in the above-mentioned station. The technical staff said that the key here is to adjust the vacuum negative pressure, not only to ensure that all unseparated capsules can be removed, but also the capsule cap in the upper module cannot be sucked away. If the vacuum is too small, bad capsules cannot be completely eliminated; if the vacuum is too large, the caps of the capsules will be sucked away, causing unnecessary waste and reducing the yield.
Fourth, the capsule locking station. This station is to fit the filled capsule into the capsule body and capsule cap, which is an important step in capsule filling.
The common problems of this station include: the capsule is inserted and split, the main reason is the poor alignment of the upper and lower modules, the capsule body and the capsule cap are not on the same center line when the capsule is locked, causing damage to the capsule body or the capsule cap; poor locking state , Including the collapse of the capsule, the damage of the capsule, the separation of the capsule body and the cap of the finished capsule. The main reason for the collapse of the head and the damage of the capsule is caused by the short locking length; the separation of the capsule body and the capsule cap is caused by the too long locking length, which causes the capsule not to be locked, and the separation of the capsule body and the cap occurs during the transportation of the capsule.
The technical staff suggested that the user should measure the locking length of the capsule when debugging the equipment before production to ensure that it is within the qualified range, so as to ensure the stable production of the capsule filling machine and the quality of the filling.
How to improve the filling quality of the capsule filling machine? Pay attention to these positions
Nov 30, 2021
Leave a message

