Hangzhou Shengde Machinery Co., Ltd. is one of the most professional manufacturers and suppliers of Double Corner Carton Labeling Machine in China. Welcome to wholesale customized Double Corner Carton Labeling Machine at competitive price from our factory. Contact us for cheap products and discount information.
Products Description
The SED-100ZTB-D is an automatic double-corner labeling machine for cartons. It handles roll-fed adhesive labels and combines product conveying, label dispensing and corner application in a coordinated process. The machine is configured around the intended product samples and label rolls, so the labeling setup corresponds to the carton and the position of its edges.
Product transport and label application
The conveyor carries the cartons into the labeling area. Guide and hold-down mechanisms support the product as it passes the labeling stations. The labeling heads, traction assemblies and corner mechanisms work with the conveyor to apply the labels at the required positions.
Each label roll follows a path through the guide rollers, sensing area, traction mechanism and dispensing plate. The traction mechanism draws the backing paper, allowing the label to separate at the dispensing edge. The backing-paper collection mechanism takes up the spent liner after the labels have been dispensed.
A product sensor detects the incoming item and sends a signal to the programmable controller. The controller processes the product and label-detection signals and controls the traction motor and the corner-application cylinder. This sequence links label feeding to the position of the product on the conveyor.
Position adjustment and controls
The labeling heads have adjustment mechanisms for height, forward and backward position, and alignment with the conveyor. The dispensing-plate angle can also be adjusted to suit label separation and the intended product position. Locking screws are released for adjustment and tightened again once the setting is established.
The operator interface provides automatic operation, manual commissioning and parameter-setting screens. Manual operation can be used to test individual movements during setup. The settings include traction speed, label-output timing and cylinder timing, allowing the sequence to be established for the product being labeled.
The control interface also provides operating counts and access to input and output status for checking sensors and actuators. An emergency-stop control is provided on the machine. The required settings should be checked with the actual carton and label before production begins.
Carton and label preparation
Format setup includes aligning the guides, selecting the labeling position and matching the label-detection point to the roll material. The product dimensions are established from the supplied samples. The applicable label and roll ranges are listed in the specification table and should be checked together when selecting a format.
The liner should be free from cuts and damage that could cause it to break during traction. Label winding should keep the strip parallel with the transport direction and maintain suitable tension through the rollers and dispensing section.
Routine care
After use, remove loose backing-paper scraps and debris from the machine. Keep the traction rollers and sensor lenses clean, and check that the label strip remains correctly guided. Label-position variation can be affected by product tolerances, head alignment, detection settings and traction-wheel condition, which should be checked during routine adjustment.
Products Specification
| Parameter | Specification |
|---|---|
| Model | SED-100ZTB-D |
| Labeling heads | 2 |
| Corner-application mechanisms | 2 |
| Reference labeling capacity | Approximately 0–100 products/min; depends on product and label dimensions |
| Product dimensions | Configured to supplied product samples |
| Label length range | 10–260 mm |
| Backing-paper width range | 10–150 mm |
| Maximum label-roll outer diameter | 300 mm |
| Label-roll core diameter | 76 mm |
| Recommended backing paper | Glassine; liner should be free from cuts and damage |
| Reference label gap | 2–3 mm, tolerance ±0.2 mm |
| Supply voltage | AC 220 V |
| Overall dimensions (L × W × H) | Approximately 2800 × 1100 × 1500 mm |
| Machine weight | Approximately 200 kg |
| Operating temperature | 0–50 °C |
| Operating relative humidity | 15–85% |
| Main mechanical materials | Stainless steel and aluminum alloy |
Features
- Coordinated carton conveying,label dispensing and corner application.
- Adjustable labeling-head position and dispensing-plate angle.
- Programmable control using product- and label-detection signals.
- Operator interface with automatic,manual and parameter-setting screens.
- Guide and hold-down assemblies for product positioning.
- Spent backing-paper collection.
- Emergency-stop control for stopping automatic operation.
Hot Tags: Double Corner Carton Labeling Machine, China, manufacturers, customized, wholesale, price, cheap, discount, Automatic Sticker Labeling Machine With Printer, Accuracy Desktop Round Bottle Automatic Labeling Machine, Labeling Machine For Round Bottles, Automatic Sticker Labeling Machine, Square Bottle Sticker Labeling Machine, Automatic One Side Self adhesive Labeling Machine


